Good-Ark — discrete power semiconductors: rectifiers, Schottky, TVS, MOSFETs, SiC and IGBT
Request a Quote
Good-Ark Engineering Blog

Articles

Browse Good-Ark engineering articles by rectifiers, protection, automotive, MOSFET, SiC, solar, Schottky, power supply, bridge, Zener, and sourcing topics.

Suzhou Good-Ark Electronics — discrete power semiconductor manufacturer

PDFN Leadless PCB Design Guide: Pads, Vias, and Solder

Updated: November 13, 2026 In a PDFN leadless package, the exposed bottom pad is the electrical and thermal exit: it carries current, conducts heat into the board, and decides whether the part performs to its datasheet. This guide covers pad design, thermal vias, stencil and reflow, and the inspection that verifies the joint—using the PDFN56 … Read more

Moisture Sensitivity Levels and Handling for SMD Rectifiers

Updated: November 11, 2026 An SMD package absorbs moisture from the air, and at reflow temperatures that moisture turns to steam inside the body—cracking the package, lifting the die, or delaminating the lead frame. The moisture sensitivity level (MSL) rating tells you how long the part can sit out before that risk appears. This guide … Read more

Bridge Rectifier Failures in Motor Drives: Field Patterns and Fixes

Bridge Rectifier Failures in Motor Drives: Field Patterns and Fixes

Updated: October 28, 2026 This page is a focused engineering note in the bridge rectifier cluster—use the checklists and links below to finish selection, not as a substitute for the datasheet. Topic hub: Bridge rectifier guide. Related deep-dives sit in the continue list at the end. Before release Pass criteria Ratings vs mission profile Voltage/current/thermal … Read more

OBC Architecture Trends: Bidirectional, High-Voltage, and Power-Dense

Updated: November 13, 2026 The on-board charger is moving in three directions at once: bidirectional power flow, higher bus voltages, and higher power density. Each trend changes the rectifier story, and this guide traces the three causal chains and their device implications. The Bidirectional Trend: V2X Changes the Power Flow Vehicle-to-everything (V2X) capability turns the … Read more

Automotive Lighting Electronics: From Halogen to Matrix LED Power Needs

Updated: October 28, 2026 This page is a focused engineering note in the automotive cluster—use the checklists and links below to finish selection, not as a substitute for the datasheet. Topic hub: 12 V automotive rail transients. Related deep-dives sit in the continue list at the end. Before release Pass criteria Ratings vs mission profile … Read more

Surge Damage in Power Supplies: Reading the Evidence

Surge Damage in Power Supplies: Reading the Evidence

The first useful number on a surged power supply is often not a joule rating. It is the official rectifier surge figure, such as the 180 A, 8.3 ms IFSM on the AMBR40250S datasheet, or the 120 A, 8.3 ms figure on the AMBRP5100 datasheet. If the board failed on a much shorter 8/20 µs event, or after many repeated … Read more

Thermal Management for a 10 A Automotive Rectifier: A Worked Case

Thermal Management for a 10 A Automotive Rectifier: A Worked Case

A 10 A automotive rectifier heading is not a thermal approval. AEC-Q101, or any similar qualification wording, records that a part was tested to a program; it does not prove that 10 A continuous in a sealed lamp or ECU housing will keep the junction inside its limit at the vehicle’s hot ambient. The counterintuitive … Read more

AWSS10H60: 10 A, 60 V Schottky for High-Current Automotive Lighting

Updated: November 19, 2026 AWSS10H60 is a Schottky rectifier rated about 10 A and 60 V in the stated package—use it when you need low forward drop at the stated current and can accept Schottky reverse leakage at high temperature. Confirm VRRM, IF(AV), VF at your IF/Tj, and the thermal path before freezing the MPN. … Read more

Solder Joint Reliability for TO-277 in Automotive LED Modules

Solder Joint Reliability for TO-277 in Automotive LED Modules

The official ASGC051BS datasheet (Rev. C) puts a 5 A, 100 V Schottky in an eSGC (TO-277B) outline with a typical 40 °C/W junction-to-ambient, 15 °C/W junction-to-case, and 7 °C/W junction-to-lead thermal resistance, measured with 30 × 30 mm copper at each terminal. Those numbers assume the exposed pad is still a continuous thermal path. In an automotive LED module, the solder joint … Read more

PV Module Power and Cell Architecture in 2026: An Industry Report

Updated: October 28, 2026 PV module power in 2026 is driven as much by cell architecture and interconnection as by raw cell efficiency headlines. For electronics readers, the practical link is how module design changes current, hotspot risk, and bypass-diode stress. The PV module industry has moved from full-cell, 60-cell panels toward half-cut cells and … Read more

Need a part number checked against your design?

Send the topology, current and voltage class. Good-Ark sales and application engineering will confirm the closest device, package and qualification status.

Copyright Suzhou Good-Ark Electronics Co., Ltd. All Rights Reserved