Good-Ark — discrete power semiconductors: rectifiers, Schottky, TVS, MOSFETs, SiC and IGBT
Request a Quote

Synchronous Rectification vs Schottky: A Beginner Decision Frame

Compare synchronous rectification with a Schottky diode using waveform-based loss, gate drive, dead time and light-load checks before selecting a power stage.

Synchronous Rectification vs Schottky: A Beginner Decision Frame

Compare two hypothetical rectifying paths carrying a flat 5 A during 60% of each switching cycle. A diode with an assumed 0.5 V forward drop dissipates 1.5 W in conduction. A driven MOSFET with an assumed hot on-resistance of 10 mΩ dissipates 0.15 W during the same interval.

The difference is attractive. It is also incomplete: the MOSFET needs correct control, and its switching, body-diode, capacitance, and drive losses remain outside that arithmetic. This comparison reviews those missing conditions rather than claiming a measured efficiency improvement.

Synchronous rectification vs Schottky: where should you begin?

Choose between synchronous rectification and a Schottky diode by comparing total loss and operating behavior in the actual circuit. A driven MOSFET can reduce conduction loss, especially at low voltage and substantial current, but adds timing and drive requirements. A Schottky offers simpler commutation, while reverse leakage, voltage rating, and thermal limits still matter.

Compare the same current interval before comparing devices

Specify the topology, voltage range, frequency, current waveform, and rectifying interval. A buck freewheel path and a flyback secondary do not have identical timing. Avoid comparing a diode’s average-current loss with a MOSFET calculation using an unrelated load current or duty factor.

The introductory example deliberately uses a rectangular current pulse. Real ripple or triangular current changes RMS current and therefore MOSFET conduction loss. For the general case, average vF(t)i(t) over the diode’s conduction interval, and average i²(t)RDS(on) over the MOSFET’s channel-conduction interval. State the temperature and gate-voltage assumptions.

Goodark MBRF20200CT insulated TO-220AB Schottky package
Goodark MBRF20200CT insulated TO-220AB Schottky package.

List the losses that the conduction estimate leaves out

For a first drive-power estimate, Qg × Vdrive × fs gives the energy needed to cycle a gate multiplied by frequency. With hypothetical values of 20 nC, 5 V, and 200 kHz, this is 0.02 W. It is a system power term distributed through the drive path, not necessarily all heat inside the MOSFET die.

Add applicable output-capacitance energy, switching overlap, body-diode conduction, recovery, and controller supply consumption. Analog Devices’ efficiency primer explains why gate drive belongs in the budget. For the diode alternative, include reverse leakage and capacitive behavior under the relevant voltage and temperature conditions.

A lower room-temperature resistance can come with greater charge or capacitance. Infineon’s synchronous-rectifier selection note evaluates several loss terms and operating modes. Its selection charts require their stated conditions; they are not a universal device ranking.

Use a comparison that includes control obligations

Questions that decide the rectification approach
Issue Schottky rectification Synchronous MOSFET rectification
Conduction estimate Forward voltage times current, averaged over time Current squared times hot on-resistance, averaged over time
Control Conduction follows circuit bias Gate timing and suitable drive required
Reverse behavior Check reverse rating, leakage and capacitance Check channel reverse current, body diode and off-state stress
Light load Forward loss falls with current Drive and control overhead can become important
Verification Voltage, current, temperature and transients Those checks plus gate timing and abnormal transitions

For another comparison of diode technologies, read Schottky versus fast-recovery trade-offs. That choice remains distinct from deciding whether active rectification and its controller are justified.

Check dead time without assuming all topologies behave alike

In a synchronous buck, overlap between the high-side and low-side switches can create a supply short. Nonoverlap timing is therefore essential. During part of that interval, inductor current may pass through the low-side MOSFET’s body diode. Excessively long dead time can increase loss, while inadequate dead time risks cross-conduction.

A flyback synchronous rectifier has different sensing and timing constraints. Its turn-off must match the transformer and operating mode. Use the intended controller’s guidance rather than copying buck timings. TI’s SMPS MOSFET selection discussion highlights body-diode and recovery considerations in synchronous service.

Review light load, startup, and an already charged output

An enhanced MOSFET channel can conduct current in either direction. That is useful in some operating modes but can permit unwanted reverse current in others. A prebiased output or a light load can therefore change the decision even when full-load conduction loss strongly favors the MOSFET.

Check whether the controller uses diode emulation, pulse skipping, forced continuous conduction, or another mode, and what it does during startup and shutdown. Analog Devices discusses these nonisolated-converter conditions. Do not assume every product called synchronous blocks reverse current.

At a flat 5 A during 60 percent conduction duty, an assumed 0.5 V diode loses 1.5 W and an assumed 10 milliohm fully enhanced MOSFET loses 0.15 W; switching and drive loss are excluded.
At a flat 5 A during 60 percent conduction duty, an assumed 0.5 V diode loses 1.5 W and an assumed 10 milliohm fully enhanced MOSFET loses 0.15 W; switching and drive loss are excluded.

Keep the surrounding discrete functions separate

A gate threshold specification does not guarantee low resistance at the available drive voltage. Consult the specified RDS(on) conditions and hot behavior. The MOSFET versus BJT switching comparison provides context for controlled devices, while half-wave and full-wave waveforms concerns rectification paths rather than synchronous gate timing.

A TVS or Zener clamp serves another purpose. Adding protection does not establish correct channel timing or adequate cooling. Every function needs its own stress and operating-condition review.

Verify loss and waveforms across the operating envelope

Compare input and output power with appropriate measurement accuracy, and examine device temperatures under matching conditions. Check rectifier current, reverse stress, gate-source voltage, and timing with suitable instruments. Hazardous energized tests require qualified personnel; follow Tektronix floating-measurement guidance when planning probe references.

Record input range, load, frequency, ambient, cooling, operating mode, and startup state. Investigate unexpected ringing or heating before attributing it solely to device technology. Layout and measurement artifacts can both mislead a comparison.

Open the controller datasheet before accepting the MOSFET option

A Schottky may remain appropriate when its losses fit the thermal budget and simple commutation is valuable. A synchronous stage may be justified when its complete loss budget improves the result and its controller handles all required modes. There is no universal current threshold for the change.

Review controller timing and protection together with the exact diode or MOSFET documentation. Retain the assumptions and full loss calculation so the decision remains valid when voltage, load, temperature, or switching frequency changes.

FAQ

Is synchronous rectification always more efficient?

No. It can substantially reduce conduction loss, but the complete result includes gate-drive power, controller consumption, capacitance-related losses, switching behavior, and body-diode conduction. At light load, some of those terms remain important while the useful output power falls. Compare the same operating conditions and required modes, then verify the actual circuit. A lower resistance number alone does not establish a better overall efficiency curve.

Can I replace a Schottky diode with a MOSFET without changing control?

Generally, no. A MOSFET used for synchronous rectification needs suitable gate drive and timing for the actual topology. Simply installing it in a diode position does not establish correct conduction or turn-off. The body diode may provide a path in one direction, but that does not deliver the intended channel-loss benefit. Review the controller, sensing, voltage stress, layout, and abnormal operating states before making that design change.

Does the smallest RDS(on) identify the best synchronous rectifier?

No. Use resistance at the relevant gate voltage and temperature, then include charge, capacitance, body-diode behavior, package thermal performance, and the switching conditions. A device with lower conduction resistance can require more drive energy or produce different commutation losses. The best candidate depends on the full current waveform and controller behavior, including light load and startup, rather than one minimum resistance entry at a laboratory condition.

Copyright Suzhou Good-Ark Electronics Co., Ltd. All Rights Reserved