Good-Ark — discrete power semiconductors: rectifiers, Schottky, TVS, MOSFETs, SiC and IGBT
Request a Quote
Good-Ark Engineering Blog

Articles

Browse Good-Ark engineering articles by rectifiers, protection, automotive, MOSFET, SiC, solar, Schottky, power supply, bridge, Zener, and sourcing topics.

Suzhou Good-Ark Electronics — discrete power semiconductor manufacturer

Breadboard Bridge Rectifier: Build It from Four 1N4007s and Verify Every Diode

Breadboard Bridge Rectifier: Build It from Four 1N4007s and Verify Every Diode

Updated: October 28, 2026 This page is a focused engineering note in the bridge rectifier cluster—use the checklists and links below to finish selection, not as a substitute for the datasheet. Topic hub: Bridge rectifier guide. Related deep-dives sit in the continue list at the end. Before release Pass criteria Ratings vs mission profile Voltage/current/thermal … Read more

Half-Wave vs Full-Wave Rectification: Reading the Waveform Instead of Memorizing Diagrams

Half-Wave vs Full-Wave Rectification: Reading the Waveform Instead of Memorizing Diagrams

Updated: November 11, 2026 Most students learn the half-wave and full-wave rectifier by memorizing two circuit diagrams and a sentence about efficiency. But on the bench, the difference the two topologies actually make appears on the oscilloscope screen — and the waveform tells you everything the diagram hides. On the same 50 Hz mains, a … Read more

Diode Test Mode: The Three Readings That Tell You Good, Open, or Shorted

Diode Test Mode: The Three Readings That Tell You Good, Open, or Shorted

Updated: November 9, 2026 Ask a repair technician how to “test a diode” and the answer usually starts with the meter instead of the reading. But the multimeter’s diode mode only produces three meaningful outcomes — a forward drop around 0.5–0.8 V in one direction, OL in the other, or the same reading both ways … Read more

SMB vs SOD-123 for TVS: Package, Pulse Power, and Placement

SMB vs SOD-123 for TVS: Package, Pulse Power, and Placement

A 600 W-class TVS in an SMB package can still fail to protect a 12 V rail if it is placed a few centimeters too far from the entry. The smaller SOD-123 device on a nearby data line can look under-rated and still do its job, because its event was smaller and its loop was … Read more

D2PAK (TO-263) Design Guide: Footprint, Copper, and Thermal Vias

D2PAK (TO-263) Design Guide: Footprint, Copper, and Thermal Vias

Updated: November 9, 2026 The D2PAK is a board-mount power package whose tab and exposed pad carry the heat into the PCB, and the board design decides whether a 30 A rating is real. This guide covers the footprint, the copper and via strategy, the soldering, and the inspection that verifies the joint—using the AMBRB … Read more

TO-277 vs SMB/SMA: The Power Rating Gap in Automotive SMDs

TO-277 vs SMB/SMA: The Power Rating Gap in Automotive SMDs

A common cross-reference treats SMA as a 1 A package, SMB as a 2 A package, and TO-277 as a 5 A package, then calls the step a power-rating gap. Official automotive Schottky listings do not follow that ladder. Good-Ark’s ASK5BA in SMA (DO-214AC), ASK5BB in SMB (DO-214AA), and ASGC051BS in eSGC (TO-277B) are all … Read more

PDFN vs DPAK: Leadless Thermal Performance for Compact Power

Updated: November 13, 2026 Both the PDFN and the DPAK move heat through an exposed pad into the board, but they serve different current classes and pay different board costs. This guide compares the thermal numbers, the layout cost, and the assembly, and says when each package wins. Leadless Packages Move Heat Through the Pad … Read more

D2PAK vs TO-220: Board Copper or Bolt-On Heatsink

Updated: November 9, 2026 D2PAK and TO-220 are both capable 30–40 A rectifier packages, but they embody two different thermal philosophies: the D2PAK turns the PCB into the heatsink, while the TO-220 bolts to an external one. The right choice follows the product’s mechanical architecture—dense board or chassis-level cooling. This article compares the two heat … Read more

SiC Schottky vs Silicon Schottky: Where the Voltage Line Moves

SiC Schottky vs Silicon Schottky: Where the Voltage Line Moves

The failure that draws the voltage line is rarely mysterious. A silicon Schottky that was happy on a 48 V or 200 V rail is asked to sit on a rising bus, or it is dropped into a hot enclosure, and the first things to move are leakage and available reverse voltage. The technician who … Read more

Need a part number checked against your design?

Send the topology, current and voltage class. Good-Ark sales and application engineering will confirm the closest device, package and qualification status.

Copyright Suzhou Good-Ark Electronics Co., Ltd. All Rights Reserved